Search found 9 matches
- Tue Nov 17, 2009 12:43 pm
- Forum: BCS Programming
- Topic: Programming Help(Control one output with two different probe
- Replies: 6
- Views: 5635
Re: Programming Help(Control one output with two different probe
Wow, Thanks for the extremely thorough response. It looks like my timing on this question is right on the money since you plan to release an update very soon. As far as the operation of my system goes, you are spot on. I have it programmed as you stated. Will this firmware upgrade be difficult to do...
- Tue Nov 17, 2009 10:50 am
- Forum: BCS Programming
- Topic: Programming Help(Control one output with two different probe
- Replies: 6
- Views: 5635
Re: Programming Help(Control one output with two different probe
I do have a two pump system that I have been using as a HERMS. I can direct fire all three kettles if needbe(direct fire assist). So currently I need to stick with my method of moving my sensors?
Here is a pic of my system nearly completed.
Here is a pic of my system nearly completed.
- Mon Nov 16, 2009 6:23 pm
- Forum: BCS Programming
- Topic: Programming Help(Control one output with two different probe
- Replies: 6
- Views: 5635
Programming Help(Control one output with two different probe
Can anyone give some programming insight? I am a new user and now have two brew days under my belt with the BCS. Here is my problem. During my preheat stage I am controlling the temp setpoint of my HLT and MLT (by turning my burners on) with a temp probe on the output of a corresponding pump because...
- Thu Sep 10, 2009 12:55 pm
- Forum: General Discussion
- Topic: New Control Panel Setup (Help with SSR's)
- Replies: 12
- Views: 7648
Re: New Control Panel Setup (Help with SSR's)
Thanks guys.
I will give this a try tonight.
Cheers
I will give this a try tonight.
Cheers
- Tue Sep 08, 2009 4:54 pm
- Forum: General Discussion
- Topic: New Control Panel Setup (Help with SSR's)
- Replies: 12
- Views: 7648
Re: New Control Panel Setup (Help with SSR's)
I have now set up my control panel and beginning to wire things but i am still unclear as to how the SSR needs to be wired. I am trying to put a switch to control the action of the SSR and am looking for advice on where to put this as well The low voltage terminals 1 - Wired to the ouput of the BCS ...
- Mon Aug 17, 2009 3:11 pm
- Forum: General Discussion
- Topic: New Control Panel Setup (Help with SSR's)
- Replies: 12
- Views: 7648
Re: New Control Panel Setup (Help with SSR's)
Thanks. I will be ordering my BCS this week hopefully. What kind of lead time will I be looking at?
- Sun Aug 16, 2009 10:18 am
- Forum: General Discussion
- Topic: New Control Panel Setup (Help with SSR's)
- Replies: 12
- Views: 7648
Re: New Control Panel Setup (Help with SSR's)
I think controlling the gas will work well. i have high hopes of the capabilities of the controller. Where did you get your SSR's? Can anyone else confirm that these SSR's will work?
- Sat Aug 15, 2009 5:16 pm
- Forum: General Discussion
- Topic: New Control Panel Setup (Help with SSR's)
- Replies: 12
- Views: 7648
New Control Panel Setup (Help with SSR's)
I am in the process of setting up my control panel and am by no means an experienced electrician. Right now i am looking to control two march pumps and three asco gas valves. I have found a crydom relay on ebay that i believe should fit my application but am not sure. Can someone take a look at this...
- Mon Aug 10, 2009 9:13 am
- Forum: BCS Expansion Cards
- Topic: BCS I/O Expansion Card
- Replies: 15
- Views: 27045
Re: BCS I/O Expansion Card
Is it worthwhile to wait for the upgrade? I am contemplating ordering this controller vs another and this would definitely make it more attractive. The added $50 does hurt slightly though because it puts the whole system with 4 probes at about $300.