Search found 12 matches
- Mon Jan 18, 2016 11:26 am
- Forum: Troubleshooting and Support
- Topic: Having trouble connecting through the router
- Replies: 4
- Views: 4146
Re: Having trouble connecting through the router
I did try to do the hard reset and still no luck with it. I believe i have the older firmware so i will try it later today. Where do i find the 3x firmware and the 4x firmware? I used the wiki find my bcs utility.
- Mon Jan 11, 2016 11:18 am
- Forum: Troubleshooting and Support
- Topic: Having trouble connecting through the router
- Replies: 4
- Views: 4146
Having trouble connecting through the router
I have a bcs 462 and have been using it directly connected to one of my old computers for a while. I got a long cat 6 cable to connect it to my router now. I turned off bcs then connected to the apple router. When I search for it with the bcs finder it doesn’t find anything. I have manually typed in...
- Thu Dec 29, 2011 10:54 pm
- Forum: Wiring, Electrical, Relays and Sensors
- Topic: How Long can the wire run be?
- Replies: 0
- Views: 19872
How Long can the wire run be?
Will a long wire run to the temp probes throw the reading off by much? I am running 75-100 feet of cat 5 from the bcs to 3 probes. is this going to throw my temps off by much?
- Wed Dec 21, 2011 10:00 am
- Forum: BCS for Pros
- Topic: Winery
- Replies: 0
- Views: 35078
Winery
I got the bcs 460 originally for my brewing hobby, but recently purchased the new 462 for our winery. The reason for doing this is because it was much cheaper than adding on new tank controllers to our original controller cabinet. When we first started i had someone wire up all the tanks and plumb t...
- Mon Dec 19, 2011 8:55 pm
- Forum: Wiring, Electrical, Relays and Sensors
- Topic: Make and model of thermistor in probe
- Replies: 11
- Views: 11488
Re: Make and model of thermistor in probe
I just purchased some of these probes .
http://www.ebay.com/itm/Thermocouple-K- ... 096wt_1344
I pluged one in and the temp was jumping all over the place in the 600s
Did i buy the wrong probes?
http://www.ebay.com/itm/Thermocouple-K- ... 096wt_1344
I pluged one in and the temp was jumping all over the place in the 600s
Did i buy the wrong probes?
- Sun Jun 13, 2010 12:42 pm
- Forum: Wiring, Electrical, Relays and Sensors
- Topic: Valves?
- Replies: 3
- Views: 4076
Re: Valves?
I will be using them for fluid. I was thinking of controlling the transfer from both my fly sparge and the transfer to the bk. I was thinking two for each step, so a total of four. I just built a float switch that will control a pump, so I can get rid of one of the pump outputs. So I should probably...
- Mon May 24, 2010 8:20 pm
- Forum: Wiring, Electrical, Relays and Sensors
- Topic: Valves?
- Replies: 3
- Views: 4076
Valves?
So far i will be controlling 2 pumps and 2 heaters with my controller, I want to control some solenoid valves. Does that mean i can only control 2 solenoid valves? What would i use the 4 Discrete Inputs for?
- Wed May 05, 2010 12:11 pm
- Forum: BCS Programming
- Topic: RIMS temperature control
- Replies: 5
- Views: 7035
Re: RIMS temperature control
How did you take your screen shots? I am trying to get some help in trouble shooting my bcs and would like to be able to post this.
- Wed May 05, 2010 8:06 am
- Forum: BCS Programming
- Topic: Newbies guide to mash (very basic)
- Replies: 4
- Views: 5064
Re: Newbies guide to mash (very basic)
Sounds just about what i have set up, but i cant get mine to work. It will run through the first state and then alarm, and stop. It never moves to the next state, and i cant even make it go to the next state. On my 3rd or 4th state when i mash out i set my temp to PWM at 25% This picks up heat when ...
- Mon May 03, 2010 8:05 pm
- Forum: Troubleshooting and Support
- Topic: BCS locking up every 60 seconds or so...
- Replies: 7
- Views: 6416
Re: BCS locking up every 60 seconds or so...
I do hook my computer straight to the bcs. I still can not get my computer back online do u have a step by step directions, because i am a ratard.