Search found 381 matches

by clearwaterbrewer
Thu Dec 07, 2017 5:42 am
Forum: Troubleshooting and Support
Topic: how to get 2 'Direct' outputs to show 'on' in same state
Replies: 12
Views: 311

Re: how to get 2 'Direct' outputs to show 'on' in same state

The safari version that ships with iOS 9.3 does not support some of the newer javascript standards and that is probably what's causing the problem. We noted that this mean no more support for IE 10 in the release notes but didn't point out the limitations on older mobile devices. I think all browse...
by clearwaterbrewer
Thu Nov 30, 2017 2:50 am
Forum: PC / Mac Apps
Topic: BCS 4.0 .NET API and BCS Temperature Logger
Replies: 56
Views: 8138

Re: BCS 4.0 .NET API and BCS Temperature Logger

Heck yeah, I'm glad it is getting used. Have you found much use for the data that comes out of it? Mostly is it for record keeping or curiosity? how hard would this be to port/adapt/whatever to run on rPi? specifically the rPi Zero W? I bought my first to use for Tilt Pi, and then bought another to...
by clearwaterbrewer
Tue Nov 28, 2017 6:41 am
Forum: Troubleshooting and Support
Topic: BCS 462 locks up
Replies: 7
Views: 275

Re: BCS 462 locks up

no connection... next time it happens I can see if a wireshark of the connection attempt shows anything.

BCS hard wired, 4.0.1
iPad - wireless (unknown version at this time)
PC - win10, chrome (latest version) - could not load website, server not responding..
by clearwaterbrewer
Tue Nov 28, 2017 6:36 am
Forum: Troubleshooting and Support
Topic: how to get 2 'Direct' outputs to show 'on' in same state
Replies: 12
Views: 311

Re: how to get 2 'Direct' outputs to show 'on' in same state

I am not in front of the iPad today, will check version tomorrow, but I have reasons to not upgrade further.

here is what I got with 4.1.1 before going back:
by clearwaterbrewer
Tue Nov 28, 2017 6:33 am
Forum: Roadmap and Feature Request
Topic: alert when upgrading firmware when backup has not been recently done
Replies: 4
Views: 118

Re: alert when upgrading firmware when backup has not been recently done

is there a way to cache the .json in memory during an upgrade and it is available only until the next power cycle? When the page refreshes after the update a button is not greyed out if that file is persistent in memory and a push of a button loads it from memory?
by clearwaterbrewer
Mon Nov 27, 2017 6:42 am
Forum: Wiring, Electrical, Relays and Sensors
Topic: Driving More than one SSR
Replies: 6
Views: 336

Re: Driving More than one SSR

A good way to do this might be to put a transistor and a few resistors in a section of shrink tube and be done with it.. Look at the schematic (in the documents section)this project, remove all but R1, R2, and Q2, and you could drive several SSR's, the 2N3904 transistor can do 200mA (and it will wor...
by clearwaterbrewer
Mon Nov 27, 2017 5:15 am
Forum: Roadmap and Feature Request
Topic: alert when upgrading firmware when backup has not been recently done
Replies: 4
Views: 118

alert when upgrading firmware when backup has not been recently done

a register set in firmware of the date the last successful backup... and a display next to the update button that says how long it is...

and then I realize bcs does not have a concept of time.. <bang head against wall>
by clearwaterbrewer
Sun Nov 26, 2017 5:11 pm
Forum: Troubleshooting and Support
Topic: BCS 462 locks up
Replies: 7
Views: 275

Re: BCS 462 locks up

No, going to a completely new PC did not help either. (this was 4.0.1, FWIW) I suspected it was still operating normally, and we had documented when a 1-hour process-state hadstarted, so we waited, and when that was done,sure enough, it went to the next state, we still could not get in, so power-cyc...
by clearwaterbrewer
Sun Nov 26, 2017 9:26 am
Forum: Troubleshooting and Support
Topic: BCS 462 locks up
Replies: 7
Views: 275

Re: BCS 462 locks up

I have just the webui portion freeze, the rest of it works just fine, it looked dead, but the timers and PIDs functioned normally, we just could not see them...
by clearwaterbrewer
Sun Nov 26, 2017 9:06 am
Forum: Roadmap and Feature Request
Topic: BCS 4.1.1 Firmware Released
Replies: 17
Views: 784

Re: BCS 4.1.1 Firmware Released

Automation is to reduce work and mistakes... Most everyone here can agree with that, right? I think most people on here go on with their lives and their brewing and can go 6-12 months or more between upgrades, and it is easy to forget in this world of upgrading your phone, your PC, etc.. that you ne...