Search found 425 matches

by brahn
Fri Jul 05, 2019 10:23 am
Forum: General Discussion
Topic: Updating firmware via USB DFU
Replies: 49
Views: 1288

Re: Updating firmware via USB DFU

I believe you're running into an issue we had with the original TI bootloader code on newer MacOS versions. Can you confirm that you're on a Mac? There's a couple ways to get through this. I updated the bootloader to fix the issue, but the bootloader on the BCS can only be flashed via JTAG which wou...
by brahn
Sat Apr 13, 2019 10:11 am
Forum: General Discussion
Topic: Updating firmware via USB DFU
Replies: 49
Views: 1288

Re: Updating firmware via USB DFU

When you power it on do you see the lights flash on the ethernet connection? If you do: try another hard reset, hold down the reset button for 15 seconds then release. Assuming it comes back on and you can see it in BCS finder, try accessing the API: http://your.bcs.ip/api/debug and see what that re...
by brahn
Thu Apr 11, 2019 6:49 pm
Forum: General Discussion
Topic: Updating firmware via USB DFU
Replies: 49
Views: 1288

Updating firmware via USB DFU

Important: After flashing via any of the methods below the BCS must be power cycled before it will leave DFU mode. Pressing the reset button is not sufficient. Windows: For Windows there are some one-time steps needed to set up a USB Driver for the BCS: 1. Download Zadig 2. Connect the BCS to the P...
by brahn
Thu Apr 11, 2019 5:16 pm
Forum: Roadmap and Feature Request
Topic: BCS 4.1.3 Firmware Release
Replies: 4
Views: 405

BCS 4.1.3 Firmware Release

The BCS firmware has been updated to 4.1.3 (build fd86a103). These are the changes in 4.1.3: Fix issue causing flash corruption on BCS-482 Performance improvements for BCS-482 Beta: Use Registers for Exit Conditions A build for BCS-460/2 will be coming later but the main changes in this release only...
by brahn
Mon Mar 19, 2018 3:28 pm
Forum: Roadmap and Feature Request
Topic: BCS 4.1.2 Firmware Release
Replies: 14
Views: 3169

Re: BCS 4.1.2 Firmware Release

A lot of the content is cached fairly aggressively in the browser to improve performance rather than loading from the BCS every time. At a minimum, a force reload of the page should be done after an upgrade.
by brahn
Sun Mar 18, 2018 10:36 am
Forum: Roadmap and Feature Request
Topic: BCS-482 Specifications (replacement for BCS-460/462)
Replies: 80
Views: 12893

Re: BCS-482 Specifications (replacement for BCS-460/462)

Other than minor changes for the different hardware components the UI is exactly the same as on the 460/2, so the alarm display in the UI remains.
by brahn
Sun Mar 18, 2018 10:30 am
Forum: Roadmap and Feature Request
Topic: BCS 4.1.2 Firmware Release
Replies: 14
Views: 3169

BCS 4.1.2 Firmware Release

The BCS firmware has been updated to 4.1.2 (build edf0fe2c). These are the changes in 4.1.2: Display temps below 0C Timers are selectable for display on main page Better display for Timer names on main page Fix issue selecting radio buttons on process editor Add warning about settings being erased t...
by brahn
Thu Nov 30, 2017 2:04 pm
Forum: Troubleshooting and Support
Topic: how to get 2 'Direct' outputs to show 'on' in same state
Replies: 12
Views: 1734

Re: how to get 2 'Direct' outputs to show 'on' in same state

The safari version that ships with iOS 9.3 does not support some of the newer javascript standards and that is probably what's causing the problem. We noted that this mean no more support for IE 10 in the release notes but didn't point out the limitations on older mobile devices. I think all browser...
by brahn
Thu Nov 30, 2017 1:54 pm
Forum: Troubleshooting and Support
Topic: BCS 462 locks up
Replies: 7
Views: 1593

Re: BCS 462 locks up

If it's happening just on Android it may have something to do with the update to allow audio alarms on mobile devices that was added in 4.1. I've been using this feature for some time on Android and iOS with no issues but Android has a lot of variation and that may be why you're seeing an issue with...
by brahn
Mon Nov 27, 2017 5:34 pm
Forum: Troubleshooting and Support
Topic: how to get 2 'Direct' outputs to show 'on' in same state
Replies: 12
Views: 1734

Re: how to get 2 'Direct' outputs to show 'on' in same state

What iOS version is running on your iPad 2?


JonW is right, the Direct ON thing is the same issue as was reported for the multiple DIN exit conditions.