Hi,
Are the BCS still be manufcatured? I notice a couple of sites that support them are no longer running like the Temperature probe calibration site.
Search found 17 matches
- Mon Jun 05, 2023 8:38 pm
- Forum: General Discussion
- Topic: Looking to purchase BCS
- Replies: 4
- Views: 22695
- Fri Jun 02, 2023 2:51 pm
- Forum: BCS Programming
- Topic: Howto: Calibrate Temperature Probes
- Replies: 45
- Views: 165981
Re: Howto: Calibrate Temperature Probes
Hi, Trying to manually do an offset, there used to be a utility where you could put in an offset of say 2C but I cant seem to find it. Alot of the links are all dead now. Could somebody please help me in the right direction please. I have opened the utility app on the settings page of the BCS but th...
- Fri Jan 31, 2014 6:30 pm
- Forum: General Discussion
- Topic: Graphing BCS Data Logs
- Replies: 2
- Views: 4689
Graphing BCS Data Logs
Has anybody used the data log to graph there temps after a brew (outside of the BCS), and if so what is the best software for automating the proccess of graphing it.
- Fri Jan 31, 2014 6:28 pm
- Forum: Troubleshooting and Support
- Topic: Temp Display Delays
- Replies: 3
- Views: 3830
Re: Temp Display Delays
Problem solved.
Did a calibration on the probes and all working fine again.
Thanks
Did a calibration on the probes and all working fine again.
Thanks
- Fri Jan 24, 2014 6:13 pm
- Forum: Troubleshooting and Support
- Topic: Temp Display Delays
- Replies: 3
- Views: 3830
Re: Temp Display Delays
Hi, I am running the latest Firmware.
Any ideas what could start causing this?
Thanks
Any ideas what could start causing this?
Thanks
- Sun Jan 19, 2014 6:04 pm
- Forum: Troubleshooting and Support
- Topic: Temp Display Delays
- Replies: 3
- Views: 3830
Temp Display Delays
I have a BCS 460, with 3 temp probes connected. The refresh rate on screen tells me I'm getting around 1.5sec refresh, yet the temperature dials on the screen only seem to refresh approx every 10-15 seconds. When I click an output the response is pretty much instant, yet temps are delayed. System is...
- Fri Jan 17, 2014 7:10 pm
- Forum: Troubleshooting and Support
- Topic: Relay Problems
- Replies: 3
- Views: 3842
Re: Relay Problems
Problem Solved, The BCS and Solenoids were on seperate power supplies and by making sure that the BCS was connected to the same power supply as the 5v Solenoids the problem resolved itself.
Thanks
Thanks
- Sun Jan 12, 2014 11:39 am
- Forum: Troubleshooting and Support
- Topic: Relay Problems
- Replies: 3
- Views: 3842
Relay Problems
Hi, I have my controller connected to 2 x 4 ch Relays and 1 x 1channel Relay. They are powered by 12volts. When all connected to the BCS I can control all outputs except OUT0, and if I turn all outputs on one after the other they will all turn on until you turn the last out put on which causes all t...
- Mon Aug 05, 2013 6:38 pm
- Forum: Troubleshooting and Support
- Topic: Random Entry is settings
- Replies: 5
- Views: 5600
Re: Random Entry is settings
OK so I have removed the expansion card and hard reset the controller, and now we are back to normal. So I am going to leave the Expansion card off (mainly cause it cant be controlled in manual mode) and see how we go. Maybe in the next firmware update, there could be a way of manually controlling t...
- Sat Jul 20, 2013 5:39 pm
- Forum: Troubleshooting and Support
- Topic: Random Entry is settings
- Replies: 5
- Views: 5600
Re: Random Entry is settings
No, I have not reloaded the firmware its still as it was out of the box. which is the latest version.
It was working fine, its just started doing it.
It was working fine, its just started doing it.