Oakbarn, what brand of contactors and breakers did you use, and where did you purchase them?
Thanks!
Search found 43 matches
- Fri Nov 16, 2018 5:54 am
- Forum: Wiring, Electrical, Relays and Sensors
- Topic: 32a double pole breaker for 220v circuit randomly trips
- Replies: 5
- Views: 17505
- Thu Nov 15, 2018 3:36 pm
- Forum: Wiring, Electrical, Relays and Sensors
- Topic: 32a double pole breaker for 220v circuit randomly trips
- Replies: 5
- Views: 17505
Re: 32a double pole breaker for 220v circuit randomly trips
Yes, thanks for that oakbarn. This makes perfect sense!
- Thu Nov 15, 2018 1:10 pm
- Forum: Wiring, Electrical, Relays and Sensors
- Topic: 32a double pole breaker for 220v circuit randomly trips
- Replies: 5
- Views: 17505
32a double pole breaker for 220v circuit randomly trips
Hello, I am running a BCS-462 in a control box with (6) 6,000w elements, each utilizing a 32a double pole breaker for 220v circuit. I am attempting to dial-in our boil kettle process using (2) elements, manually running them directly from the panel switches. Nothing else is being used. (2) volt/amp ...
- Mon Sep 17, 2018 2:14 pm
- Forum: Troubleshooting and Support
- Topic: Current Software Version
- Replies: 5
- Views: 5925
Re: Current Software Version
Thanks, Jon. I understand that I can disable them. My issue is that I have a few auxiliary probes that are set up for multiple uses and they are unplugged when not in use but must remain enabled. I run a 2.5 BBL system and use all 8 probes. I have a large TV monitor mounted high on a wall in our bre...
- Mon Sep 17, 2018 11:52 am
- Forum: Troubleshooting and Support
- Topic: Current Software Version
- Replies: 5
- Views: 5925
Re: Current Software Version
I successfully installed v4.1.2. The question I have is why are all of my temperature probes that are unplugged reading -3276.8? They read correctly when plugged in.
- Mon Sep 17, 2018 5:12 am
- Forum: Troubleshooting and Support
- Topic: Current Software Version
- Replies: 5
- Views: 5925
Re: Current Software Version
Thanks, Jon!
- Sun Sep 16, 2018 11:37 am
- Forum: Troubleshooting and Support
- Topic: Current Software Version
- Replies: 5
- Views: 5925
Current Software Version
Sorry if this is obvious and I am missing it......can someone tell me definitively where I can check to verify that I am running the most current version?
Thank you!
Thank you!
- Fri Jul 07, 2017 12:44 pm
- Forum: Wiring, Electrical, Relays and Sensors
- Topic: BCS Float Switch Cable Pin Assignment
- Replies: 4
- Views: 15645
Re: BCS Float Switch Cable Pin Assignment
Thank you, oakbarn & Jon. This box is running 60a x2 and a BCS-462. Ryan at EBS has (4) float switch XLR wired at the box utilizing pins 2 and 3 (side pins of the 3-pin triangle). For each XLR, one of the two wires is run to an element switch on the panel and the other to a relay, and then on to...
- Thu Jul 06, 2017 4:48 pm
- Forum: Wiring, Electrical, Relays and Sensors
- Topic: BCS Float Switch Cable Pin Assignment
- Replies: 4
- Views: 15645
Re: BCS Float Switch Cable Pin Assignment
Thanks for the reply, Jon. My control box was a custom build by Electric Brewing Supply. I did email them about this, but no reply. From the inside of the box, it appears that the XLR's are wired using pins 1 & 2 (side pins if 3-pin triangle). I will insure that the DINs are enabled and assigned...
- Thu Jul 06, 2017 2:24 pm
- Forum: Wiring, Electrical, Relays and Sensors
- Topic: BCS Float Switch Cable Pin Assignment
- Replies: 4
- Views: 15645
BCS Float Switch Cable Pin Assignment
Hello, I am using 2 wires of a 3-wire 22 gauge cable for float switches. I have XLR connectors at the control box and M12 quick-dissconects at the float switch. My float switches are the 1.5" TC stainless side mount type. Can someone inform me of the correct XLR/M12 pin assignment? I have tried...