Search found 96 matches
- Wed Dec 14, 2016 11:20 am
- Forum: Wiring, Electrical, Relays and Sensors
- Topic: Stepper Motor Control
- Replies: 3
- Views: 11393
Re: Stepper Motor Control
It's pretty far out the box. I suggest you use an analog hydro static pressure sensor. The BCS can't read it, but you can use an arduino or a threshold switch like http://automation.supply/products/mini- ... lue-switch.
- Fri Jun 03, 2016 2:03 pm
- Forum: General Discussion
- Topic: Duda Diesel Plate Chiller
- Replies: 2
- Views: 5528
Re: Duda Diesel Plate Chiller
That's cause it clogged up and had no flow! Bwaaaahaaaaaaa!!
Ok, just kidding. Yes, PC's work well!
Ok, just kidding. Yes, PC's work well!
- Fri Apr 01, 2016 12:54 pm
- Forum: PC / Mac Apps
- Topic: BCS Desktop App (V 0.5.0) for Windows, Linux, Mac & Rpi
- Replies: 81
- Views: 2845458
Re: BCS Desktop App (V 0.5.0) for Windows, Linux, Mac & Rpi
Yes, I did the install correctly.
I may have a wheezy card, let me see if that's possible.
I may have a wheezy card, let me see if that's possible.
- Mon Mar 28, 2016 6:04 pm
- Forum: PC / Mac Apps
- Topic: BCS Desktop App (V 0.5.0) for Windows, Linux, Mac & Rpi
- Replies: 81
- Views: 2845458
Re: BCS Desktop App (V 0.5.0) for Windows, Linux, Mac & Rpi
I was able to run it on the PC.
Maybe a Jessie issue... don't know. I will try to send you the output.
-BD
Maybe a Jessie issue... don't know. I will try to send you the output.
-BD
- Mon Mar 28, 2016 2:50 pm
- Forum: PC / Mac Apps
- Topic: BCS Desktop App (V 0.5.0) for Windows, Linux, Mac & Rpi
- Replies: 81
- Views: 2845458
Re: BCS Desktop App (V 0.5.0) for Windows, Linux, Mac & Rpi
I didn't change anything other than the IP address in the config-settings.xml. It is therefore loading config-layout-jonw.xml
Unless you are talking about different XML?
Unless you are talking about different XML?
- Mon Mar 28, 2016 2:28 pm
- Forum: PC / Mac Apps
- Topic: BCS Desktop App (V 0.5.0) for Windows, Linux, Mac & Rpi
- Replies: 81
- Views: 2845458
Re: BCS Desktop App (V 0.5.0) for Windows, Linux, Mac & Rpi
No luck for me... crashes harder than Mr. Magoo piloting an F15. At first the main screen comes up, then when I go to the settings tab it crashes. I figured this was due to the wrong IP, so I edited the config file and entered the correct IP. Now it crashes right upon startup. I am running RPi 2 vB,...
- Mon Mar 28, 2016 1:37 pm
- Forum: Wiring, Electrical, Relays and Sensors
- Topic: Self Latching Relay
- Replies: 20
- Views: 33072
Re: Self Latching Relay
OK, now I have no idea what you are trying to do. You are trying to latch an input to the BCS?
- Mon Mar 28, 2016 1:33 pm
- Forum: PC / Mac Apps
- Topic: BCS Desktop App (V 0.5.0) for Windows, Linux, Mac & Rpi
- Replies: 81
- Views: 2845458
Re: BCS Desktop App (V 0.5.0) for Windows, Linux, Mac & Rpi
So, not sure from reading above... will this work on Jessie?
- Sat Mar 26, 2016 8:18 am
- Forum: Wiring, Electrical, Relays and Sensors
- Topic: Self Latching Relay
- Replies: 20
- Views: 33072
Re: Self Latching Relay
As you noted, use a latching relay. It will require two outputs on the BCS: one to latch and one to reset. The trick is to note that the BCS outputs can only drive a few milliamps, and the relay you are designing in will have a contact rating (that must exceed the circuit power you are switching dow...
- Sat Mar 26, 2016 8:01 am
- Forum: Wiring, Electrical, Relays and Sensors
- Topic: Convert from pin header to screw terminal
- Replies: 4
- Views: 6368
Re: Convert from pin header to screw terminal
My bet is that board will not work.