Search found 31 matches
- Fri Jun 23, 2017 10:45 am
- Forum: PC / Mac Apps
- Topic: My version of the HMI builder
- Replies: 104
- Views: 2058394
Re: My version of the HMI builder
I agree that a pipe T, and corners would be super helpful. Or the ability to flip the current corner pieces so the flow lines are correct. Any closer to adding a widget for a 3-way valve with "t-port" and also one with an "L-port"?
- Thu Apr 27, 2017 12:29 pm
- Forum: Troubleshooting and Support
- Topic: Can't connect to BCS updating 4.0.0 to 4.0.1
- Replies: 9
- Views: 13996
Re: Can't connect to BCS updating 4.0.0 to 4.0.1
Correct me if I'm wrong, but the router that the BCS is directly plugged into has a DHCP reservation for the BCS's MAC address. So, the router should only assign the BCS that ip address. Which is 192.168.0.10.
- Thu Apr 27, 2017 10:37 am
- Forum: Troubleshooting and Support
- Topic: Can't connect to BCS updating 4.0.0 to 4.0.1
- Replies: 9
- Views: 13996
Re: Can't connect to BCS updating 4.0.0 to 4.0.1
So how could I tell if the file was corrupted or not? I downloaded from link on sticky page. Then if that was the case how would I be able to reflash BCS myself with a good copy of firmware? I could not get 15sec reset to work.
- Thu Apr 27, 2017 8:01 am
- Forum: Troubleshooting and Support
- Topic: Can't connect to BCS updating 4.0.0 to 4.0.1
- Replies: 9
- Views: 13996
Re: Can't connect to BCS updating 4.0.0 to 4.0.1
Its not listed in the logs I already checked. I checked from 192.168.0.2-192.168.0.254, its not connected. I spoke with BH and I had already tried everything they recommended. They said it needed to be reflashed....
- Wed Apr 26, 2017 8:12 am
- Forum: Troubleshooting and Support
- Topic: Can't connect to BCS updating 4.0.0 to 4.0.1
- Replies: 9
- Views: 13996
Re: Can't connect to BCS updating 4.0.0 to 4.0.1
Also the orange light is steady and the green light is flashing randomly. Not sure if that helps.
- Wed Apr 26, 2017 8:00 am
- Forum: Troubleshooting and Support
- Topic: Can't connect to BCS updating 4.0.0 to 4.0.1
- Replies: 9
- Views: 13996
Can't connect to BCS updating 4.0.0 to 4.0.1
I was in the process of updating BCS-462 from 4.0.0 to 4.0.1. I followed all instructions from the update thread. Everything seemed to be going great until end of update when the BCS restarted and since could not find it since. The BCS is normally connected via ethernet to a bridge router. The route...
- Sat Feb 25, 2017 8:12 am
- Forum: Troubleshooting and Support
- Topic: Read-Only sign on
- Replies: 4
- Views: 7510
Re: Read-Only sign on
Ahh, didn't know that had changed. My authentication page said the sign-in was Read-Only. It's working now w/bcs as read only user name. Thanks
- Fri Feb 24, 2017 4:42 pm
- Forum: Troubleshooting and Support
- Topic: Read-Only sign on
- Replies: 4
- Views: 7510
Re: Read-Only sign on
4.0.0, I've tried the default and a specified password.
- Fri Feb 24, 2017 12:42 pm
- Forum: Troubleshooting and Support
- Topic: Read-Only sign on
- Replies: 4
- Views: 7510
Read-Only sign on
I can't get Read-Only sign-in to work. I have added password protection and am able to use Admin sign-in. I can not figure out why the read only will not work. I would like to use the read only to monitor fermentors and to allow others to view. Any ideas?
- Mon Sep 26, 2016 1:41 pm
- Forum: Wiring, Electrical, Relays and Sensors
- Topic: SSR vs. DPDT relays
- Replies: 4
- Views: 17425
Re: SSR vs. DPDT relays
Should I add fuses anywhere in the panel? I was considering putting a 15Amp fuse on the 110V AC hot leg prior to the hot bus.