Search found 9 matches

by MiguelG
Fri May 29, 2020 12:28 pm
Forum: Troubleshooting and Support
Topic: BCS 482 Problems
Replies: 2
Views: 206

Re: BCS 482 Problems

I did a reset and it came back online, back on the web interface. The outputs still don't work and two of them are constantly. I reached out to Brewers hardware already and they said to reach out to you.
by MiguelG
Mon May 25, 2020 1:19 pm
Forum: Troubleshooting and Support
Topic: BCS 482 Problems
Replies: 2
Views: 206

BCS 482 Problems

My bcs 482 has recently crashed. This is not the first time it has done this. However, this time I am unable to do a flash on it with the drivers/software provided on this site. The controller is now constantly turning on two outputs and the rest are dead. I can still see all of the temp probes rega...
by MiguelG
Wed May 22, 2019 10:57 am
Forum: Troubleshooting and Support
Topic: BCS-482 Can't change set points
Replies: 8
Views: 2382

Re: BCS-482 Can't change set points

Ok, that worked thanks!
by MiguelG
Wed May 22, 2019 10:10 am
Forum: Troubleshooting and Support
Topic: BCS-482 Can't change set points
Replies: 8
Views: 2382

Re: BCS-482 Can't change set points

When i move the output control setting to hysteresis the message up top says setting could not be saved.
by MiguelG
Wed May 22, 2019 10:01 am
Forum: Troubleshooting and Support
Topic: BCS-482 Can't change set points
Replies: 8
Views: 2382

Re: BCS-482 Can't change set points

I'm using Chrome.
by MiguelG
Wed May 22, 2019 9:40 am
Forum: Roadmap and Feature Request
Topic: BCS 4.1.3 Firmware Release
Replies: 10
Views: 7210

Re: BCS 4.1.3 Firmware Release

I found this and it downloads but still wont work. I can find the file with the flash utility but it doesn't flash. I just get a blank dialog box and the List devices and flash buttons become inactive. If i press the list devices button the same thing happens.
by MiguelG
Wed May 22, 2019 9:37 am
Forum: Troubleshooting and Support
Topic: BCS-482 Can't change set points
Replies: 8
Views: 2382

Re: BCS-482 Can't change set points

I used to be able to set the temperature by going to Temp Setpoint Adjust. now there is no information there. The arrows on the main control panel are also gone. I went into process/state and tried to set up the outputs to hysteresis but the heat/cool drop down, temp probe, setpoint and swing tab st...
by MiguelG
Wed May 22, 2019 8:08 am
Forum: General Discussion
Topic: Updating firmware via USB DFU
Replies: 54
Views: 18483

Re: Updating firmware via USB DFU

I downloaded the zip file and there is no DFU file when i browse in the utility program. List devices just makes the dialog box lock up and flash gives me the select a file screen. :?:
by MiguelG
Wed May 22, 2019 4:45 am
Forum: Troubleshooting and Support
Topic: BCS-482 Can't change set points
Replies: 8
Views: 2382

BCS-482 Can't change set points

I will preface this with the fact that I am not too familiar with all the tech lingo. My BCS-482 disappeared from the network last week. I thought it was a router problem so i reset the router. The BCS showed back up with a different IP address. I was able to connect to it and it was working normall...