Search found 846 matches
- Fri Aug 15, 2014 4:47 pm
- Forum: Roadmap and Feature Request
- Topic: BCS 4.0 Alpha Preview
- Replies: 47
- Views: 35755
Re: BCS 4.0 Alpha Preview
In your original posts the Web Buttons are there. I also did not see Registers Asserted on the Process Page. Assume they are still the same method?
- Fri Aug 15, 2014 4:40 pm
- Forum: Roadmap and Feature Request
- Topic: BCS 4.0 Alpha Preview
- Replies: 47
- Views: 35755
Re: BCS 4.0 Alpha Preview
Deleted as I found the answer.
- Wed Aug 13, 2014 5:37 pm
- Forum: Roadmap and Feature Request
- Topic: Temp Gauges Only Page
- Replies: 1
- Views: 2654
Temp Gauges Only Page
Be nice to have a temp Only page. I have two monitors and two computers. I have a large screen over by my Brew setup that I use just to monitor temps. If the Gauges filled the screen it would be easier for an old guy to read from his lounge chair. In fact I have several old computers laying around a...
- Thu Aug 07, 2014 11:52 am
- Forum: Troubleshooting and Support
- Topic: 2 Outs Control same SSR?
- Replies: 1
- Views: 2098
2 Outs Control same SSR?
Until 4.0 comes out, I want to change the Temp Probe Association with an Out. Right Now Out0 is associated with Temp4 in Process 0:State 0 Controls SSR#1 (HLT Element) Can I also do the following Out 1 associated with Temp 1 in Process0:State 1 SSR#1 (HLT Element) That means I would have the control...
- Thu Aug 07, 2014 10:16 am
- Forum: Wiring, Electrical, Relays and Sensors
- Topic: Momentary buttons for Dins
- Replies: 4
- Views: 4433
Re: Momentary buttons for Dins
If you are going to use DINS, I would suggest that you do not get momentary ones except to cancel an Alarm (See Ladder Logic in the Wiki). The DINs are mostly used in Ladder Logic and if momentary will trigger the Ladder Event only while depressed. You can basically make a toggle switch momentary by...
- Tue Aug 05, 2014 7:18 pm
- Forum: Troubleshooting and Support
- Topic: 7-Segment displays quit working suddenly
- Replies: 32
- Views: 19288
Re: 7-Segment displays quit working suddenly
I have an issue as well. I have 2 BCS 462's and on one the 7 segment worked fine. One the second it is hit or miss. I sent back the "good" bcs because it was not putting out a 5 v on the 5v or the outs so I cannot test it yet.
- Mon Aug 04, 2014 3:30 pm
- Forum: Troubleshooting and Support
- Topic: 7-Segment displays quit working suddenly
- Replies: 32
- Views: 19288
Re: 7-Segment displays quit working suddenly
My 7 digit wire diagram
- Mon Aug 04, 2014 3:25 pm
- Forum: Roadmap and Feature Request
- Topic: Alternate PID
- Replies: 3
- Views: 3347
Re: Alternate PID
Yahoo!!!
- Mon Aug 04, 2014 9:53 am
- Forum: Roadmap and Feature Request
- Topic: Alternate PID
- Replies: 3
- Views: 3347
Alternate PID
Would be excellent to also be able to change the Temp Probe associated with the OUT. I have an element that I would like to heat and maintain with a probe inside the pot but latter switch to a different probe in a line to control the element with a PID State 0 = Strike = Heat Strike to 166.3 Out 0 =...
- Sat Aug 02, 2014 12:09 pm
- Forum: General Discussion
- Topic: Sign Up to User for Wiki
- Replies: 0
- Views: 26865
Sign Up to User for Wiki
Where do you get an account to edit the Wiki?