Search found 96 matches
- Sat Mar 26, 2016 7:58 am
- Forum: General Discussion
- Topic: BCS tools
- Replies: 19
- Views: 11610
Re: BCS tools
Thanks for fixing! Sorry I couldn't test it further.
- Thu Feb 04, 2016 7:50 pm
- Forum: General Discussion
- Topic: BCS tools
- Replies: 19
- Views: 11610
Re: BCS tools
Hey bbrally, Everytime I try to rearrange states in process 3 (aka the fourth process) using your tool, it screws the states up. Specifically, I am moving State 0 to State 1, 1 to 2, 2 to 3, and moving the blank state 3 up to 0. Just drag and dropping, but afterward its all screwed up, dragging in s...
- Fri Jan 08, 2016 8:58 am
- Forum: Troubleshooting and Support
- Topic: Trouble Boiling
- Replies: 3
- Views: 2929
Re: Trouble Boiling
First, would run it full on (no PID, no Duty, just ON). Make sure the element is putting out full power. Use an ammeter and measure that the element is drawing the full 23-ish amps. Perhaps the SSR is not working or the element is bad - need to confirm this first.
- Sun Jan 03, 2016 3:28 pm
- Forum: BCS Programming
- Topic: DINS to adjust Duty Cycle in 4.0?
- Replies: 4
- Views: 3878
Re: DINS to adjust Duty Cycle in 4.0?
I agree. This should be accomplish-able via ladder logic. Ladder has so much room for possible expansion/improvement.
-BD
-BD
- Sun Jan 03, 2016 3:27 pm
- Forum: General Discussion
- Topic: Automated Valves - Are They Worth It?
- Replies: 6
- Views: 5745
Re: Automated Valves - Are They Worth It?
You would never successfully get high volume flow with no restriction through a non-piloted solenoid valve. And piloted valves need a good bit of pressure to open them and have extra ports to collect junk. Also, solenoids use much more power than ball valves. The best for brewing is a motorized TC b...
- Sat Dec 19, 2015 4:47 pm
- Forum: BCS Programming
- Topic: How to spawn a nested process and one once?
- Replies: 9
- Views: 6830
Re: How to spawn a nested process and one once?
Great points oakbarn!!
-BD
-BD
- Thu Dec 17, 2015 9:57 pm
- Forum: BCS Programming
- Topic: How to spawn a nested process and one once?
- Replies: 9
- Views: 6830
Re: How to spawn a nested process and one once?
I have one process left. I could use that but hate to commit 3 processes to cleaning.
Your last idea makes the most sense. Just leave the last state waiting for input. Thanks!!
-BD
Your last idea makes the most sense. Just leave the last state waiting for input. Thanks!!
-BD
- Tue Dec 15, 2015 9:55 pm
- Forum: Roadmap and Feature Request
- Topic: pine64 - the $15 64-bit single board computer
- Replies: 2
- Views: 9801
Re: pine64 - the $15 64-bit single board computer
Why would this be dramatically or functionally different than an RPi of an Arduino for i/o?
You could create a controller from either but would not be turnkey. As you said, its about the software.
-BD
You could create a controller from either but would not be turnkey. As you said, its about the software.
-BD
- Tue Dec 15, 2015 9:51 pm
- Forum: BCS Programming
- Topic: How to spawn a nested process and one once?
- Replies: 9
- Views: 6830
Re: How to spawn a nested process and one once?
Both processes are using all the available states. For rinse, it is: Prep, pre-fill, fill, level, rinse, rinse chillers, dump, dump&clean. For clean, it is: Prep, pre-fill, fill, level, rinse&heat, rinse chillers, pause, dump. If you want to know what these mean, they are: prep=get valves in...
- Mon Dec 14, 2015 7:59 pm
- Forum: BCS Programming
- Topic: How to spawn a nested process and one once?
- Replies: 9
- Views: 6830
How to spawn a nested process and one once?
I have a programming process issue I would like help with... I have an automatic cleaning cycle programmed to run in two processes. The first process is a rinse cycle, where my kettles are filled with water, recirculated, then dumped. The second process is a clean cycle, where the kettles are also f...