Search found 51 matches
- Wed Dec 23, 2015 1:50 pm
- Forum: General Discussion
- Topic: Ramp down a fermenter
- Replies: 2
- Views: 2433
Ramp down a fermenter
I'm tryin to ramp down a fermenter ive set my ramp at start temp 18c and end temp 6c and time at 24H, and ive set the output control to cool and hysteresis with a set point of 6 and a swing of 1, when I enter these details it resets the temp in the output control to 17.9 I cant work out why. Where h...
- Wed Dec 16, 2015 1:32 pm
- Forum: General Discussion
- Topic: Automated Valves - Are They Worth It?
- Replies: 6
- Views: 5891
Re: Automated Valves - Are They Worth It?
I'm trailing auto valves using an Arduino, and hall sensors to monitor fluid flow, I'm finding there not perfect, the swing on the valves is a bit too much (ie too open then too closed), theres an over run too, but this can be taken care off in the software. These can work very well if you can get t...
- Thu Sep 24, 2015 12:28 pm
- Forum: Roadmap and Feature Request
- Topic: BCS 4.0.0 firmware released
- Replies: 21
- Views: 79016
Re: BCS 4.0.0 firmware released
This new version looks great guys.
Very well done
Pesh
Very well done
Pesh
- Tue Jun 10, 2014 1:03 pm
- Forum: BCS Programming
- Topic: Help setting up Dins please
- Replies: 6
- Views: 5153
Re: Help setting up Dins please
I was working on the ladder logic ui for 4.0 last night and played with this a bit. It turns out that a process spawned via ladder logic runs as long as the coil is hot (in this case as long as the switch is closed). That means you can't use a one-shot din or kill the process from the ui if you star...
- Tue Jun 10, 2014 11:43 am
- Forum: BCS Programming
- Topic: Help setting up Dins please
- Replies: 6
- Views: 5153
Re: Help setting up Dins please
" If you are triggering this from an Arduino, you need to use a 5V input to the DIN. You will also need the grounds of the BCS and the Arduino power supply tied together." an you please clarify this Jon, is this on the 5V side or the 240V side ? I didnt think of doin this Thanks Pesh
- Mon Jun 09, 2014 3:47 pm
- Forum: BCS Programming
- Topic: Help setting up Dins please
- Replies: 6
- Views: 5153
Help setting up Dins please
So im trying to set up an Input to Din0 this starts heating the mash tun and runs a rims pump, i have an imput coming from an arduino but cant work out how to set the Din, the only way i can see how to do it is through the ladder logic page, so using ladder logic i can get the signal in but then can...
- Wed May 28, 2014 1:46 pm
- Forum: Wiring, Electrical, Relays and Sensors
- Topic: Help with Output's please
- Replies: 5
- Views: 5218
Re: Help with Output's please
Ok so ive been playing with my 2 bsc's and in getting 3.4v on all outputs on both so i guess it was just summat id done wrong.
Pesh
Pesh
- Tue May 27, 2014 6:11 am
- Forum: Wiring, Electrical, Relays and Sensors
- Topic: Help with Output's please
- Replies: 5
- Views: 5218
Re: Help with Output's please
Ok thats a fair comment thanks.
Pesh
Pesh
- Mon May 26, 2014 1:54 pm
- Forum: Wiring, Electrical, Relays and Sensors
- Topic: Help with Output's please
- Replies: 5
- Views: 5218
Re: Help with Output's please
Im getting a voltage but its different every time ( i think this is because im holding the conections in my hand ) and usually around 0.4v So im using http://www.amazon.co.uk/gp/product/B003NEGZLS/ref=oh_details_o04_s00_i00?ie=UTF8&psc=1, can you please confirm i should conect the red wire to V(...
- Sun May 25, 2014 3:34 pm
- Forum: Wiring, Electrical, Relays and Sensors
- Topic: Help with Output's please
- Replies: 5
- Views: 5218
Help with Output's please
Im tryin to test a rim's pump set up im using output0 to send a signal to an ssr to run the pump, i can get this set up to work using an Arduino uno but not the bsc, i can see the output turn green on the main page so i should be getting an out put and that should turn on the pump, all out puts sign...