Search found 846 matches
- Sat Oct 27, 2018 8:35 pm
- Forum: BCS Programming
- Topic: BCS 460 Dead?
- Replies: 10
- Views: 22328
Re: BCS 460 Dead?
Try a 15 Second Reset. It does not need anything but power to do that.
- Thu Oct 25, 2018 7:29 am
- Forum: General Discussion
- Topic: Thanksgiving & BCS
- Replies: 4
- Views: 9601
Re: Thanksgiving & BCS
I have used the BCS to control non brewing gadgets. While I have not done the Turkey fryer, it seems to me that the same principal applies to commercial french fry fryers. I know some have an element that heats the oil.
https://www.webstaurantstore.com/docume ... 4espec.pdf
https://www.webstaurantstore.com/docume ... 4espec.pdf
- Thu Oct 25, 2018 7:17 am
- Forum: Troubleshooting and Support
- Topic: BCS Not Connecting Issue
- Replies: 5
- Views: 11720
Re: BCS Not Connecting Issue
:) It happened to me the other day as well. I had a backup. :) I cannot remember what I was doing but it may have been in the Process Editor portion of the UI. I know that it was in the Process Editor portion of the UI when you have restored from a 462 Backup. This time I had built from scratch, but...
- Wed Oct 24, 2018 11:04 am
- Forum: General Discussion
- Topic: Differential Setpoint for Glycol Cooled Fermenter
- Replies: 7
- Views: 19735
Re: Differential Setpoint for Glycol Cooled Fermenter
I think you are over complicating the issue. It would work as you have it but My Glycol is only pumped into the Jacket as needed to cool. I have: State 0: Cool Glycol Bath Output 0: Glycol Chiller: Hysteresis: Glycol Bath Probe SetPoint 50 Hysteresis Swing 3 Exit Manually When I have transferred the...
- Mon Oct 22, 2018 5:35 am
- Forum: General Discussion
- Topic: Differential Setpoint for Glycol Cooled Fermenter
- Replies: 7
- Views: 19735
Re: Differential Setpoint for Glycol Cooled Fermenter
Yes. You can set an exit point based upon different criteria
DINs
Temperature
Time
You can loop between two and even have two different exits that go to a different state.
I would generally say if you can provide the logic, the BCS can follow the logic!
DINs
Temperature
Time
You can loop between two and even have two different exits that go to a different state.
I would generally say if you can provide the logic, the BCS can follow the logic!
- Fri Oct 19, 2018 12:51 pm
- Forum: General Discussion
- Topic: Touch Screen Interface for BCS
- Replies: 1
- Views: 4065
Re: Touch Screen Interface for BCS
Any tablet or pc with a modern browser will work. A chrome tablet. Would be great. I use my iPhone 6s all the time I have a large screen tv hooked up with either an HDMI cable or a chrome cast. The tv is mounted too high to use a touch screen but I also have an old cheap 11 inch notebook I use to co...
- Mon Oct 08, 2018 6:33 am
- Forum: Troubleshooting and Support
- Topic: UI Not Rendering on iPad
- Replies: 5
- Views: 10927
Re: UI Not Rendering on iPad
There is no fix. Original IPads cannot run up to date OS due to poor memory for operating system. The Old IPads on had 256mb for the OS. The IPad Air 2 has 2gb. The newer updated browser that is with the OS has features that are not supported in older browsers. Both Apple and Microsoft like to force...
- Tue Sep 25, 2018 2:18 pm
- Forum: Troubleshooting and Support
- Topic: Hard Failure
- Replies: 0
- Views: 92129
Hard Failure
I thought I had solved this with a From the Ground Rebuild of my 482 Processes. But it seems that there is an issue somewhere still. It was very common when I restored from a 462 Backup. Today (09/25/19) , I was preheating some water and clicking the Down Widget on Temp 4 LED (Controlling Out 1) und...
- Sun Sep 23, 2018 5:45 pm
- Forum: Troubleshooting and Support
- Topic: BCS-482 Unresponsive
- Replies: 15
- Views: 14848
Re: BCS-482 Unresponsive
I used to set up a Static IP. That works fine until you do a Reset or install new firmware. It then reverts to DCHP. Changing Routers will make the DCHP different. In some cases, even some change in your network can cause a re assignment, but I have had that only happen once. Under "normal"...
- Tue Sep 18, 2018 3:15 pm
- Forum: General Discussion
- Topic: problems changing config files
- Replies: 12
- Views: 13753
Re: problems changing config files
I find this one the easiest to use:
https://sourceforge.net/projects/tftputil/
Sometimes I have to try several times before I get it to work.
https://sourceforge.net/projects/tftputil/
Sometimes I have to try several times before I get it to work.