Just recieved my bsc 460 and i cant connect to it at all in fact im not convinced it has any power to it at all either, im in the uk and have an adaptor to run the unit but cant get any sence out of it at all i have 2 bsc 460 units and both are the same ive tryed all the advice on the forum and the bsc finder program too and still nothing which is making me think its a power problem.
Any advice ???
Thanks in advance
Pesh
Cant conect to bsc 460
Re: Cant conect to bsc 460
Are you getting the orange light when connected to power? http://www.embeddedcc.com/wiki/index.ph ... to_the_BCS
Re: Cant conect to bsc 460
If both are experiencing the same problem I would look to the power conversion / adapter. Check the voltage to make sure the power supply is distributing the right power with the adapters.
Re: Cant conect to bsc 460
Have you taken the MAC Address of each BCS and reserved an IP address for each in your Router config so that you can connect?
Off We Go Into The Wild Brew Yonder!
Re: Cant conect to bsc 460
Ok so theres no orange lights ( i take it you mean from the cat 5 conection)
The adaptor im using is http://www.amazon.co.uk/Stepdown-240-12 ... 766&sr=1-4
which should do the job but im still getting the same thing wich is nothing so cant find the mac address
Pesh
The adaptor im using is http://www.amazon.co.uk/Stepdown-240-12 ... 766&sr=1-4
which should do the job but im still getting the same thing wich is nothing so cant find the mac address
Pesh
Re: Cant conect to bsc 460
Things to try:
Do you have a mulitmeter? Check for proper voltage and polarity (6-10vdc and center pin positive) at the power connector.
Try a different ethernet cable. There could be a problem with the one you're using.
Connect directly to the BCS, no router. Check firewalls.
Reset the BCS (http://www.embeddedcontrolconcepts.com/ ... Hard_Reset) Press for 20 - 30 seconds and then try http://192.168.0.63
Do you have a mulitmeter? Check for proper voltage and polarity (6-10vdc and center pin positive) at the power connector.
Try a different ethernet cable. There could be a problem with the one you're using.
Connect directly to the BCS, no router. Check firewalls.
Reset the BCS (http://www.embeddedcontrolconcepts.com/ ... Hard_Reset) Press for 20 - 30 seconds and then try http://192.168.0.63
Move, copy, clear proc/states: http://manipulator.from-ca.com/
Perform coeff. mods: http://calculator.from-ca.com/
HMI latest ver: http://bbrally.altervista.org/guibeta/i ... r=01042020
Perform coeff. mods: http://calculator.from-ca.com/
HMI latest ver: http://bbrally.altervista.org/guibeta/i ... r=01042020
Re: Cant conect to bsc 460
OK so i dont have a milti meter so cant check the voltage but the adapetrs new so should be working
Checked the cat 5 cable on a network drive and that works tryed a 20 second reset and nothing seams to have happened and i still dont have any orange lights
Pesh
Why is nowt easy
Checked the cat 5 cable on a network drive and that works tryed a 20 second reset and nothing seams to have happened and i still dont have any orange lights
Pesh
Why is nowt easy
Re: Cant conect to bsc 460
Oh aye a further note i notived on the reset instructions it says if you do a 30+ second rest it defaults to 192.168.0.68 my printer was set to this and is now turned off so shouldnt be causing ip conflicts
Pesh
Pesh
Re: Cant conect to bsc 460
I'd find a multimeter. Brand new doesn't always equal working.
Move, copy, clear proc/states: http://manipulator.from-ca.com/
Perform coeff. mods: http://calculator.from-ca.com/
HMI latest ver: http://bbrally.altervista.org/guibeta/i ... r=01042020
Perform coeff. mods: http://calculator.from-ca.com/
HMI latest ver: http://bbrally.altervista.org/guibeta/i ... r=01042020
Re: Cant conect to bsc 460
Right ive aquired a multi meter and the adaptor does appear to be working so im guessing the faults with the power supply unit or the bsc unit returning eithers gonna be a pain as im in the UK
Pesh
Pesh