BCS tools

Suggestions, Problems, Availability, etc. Everything is up for discussion.
User avatar
bbrally
Posts: 210
Joined: Sat Mar 27, 2010 3:59 am
Bot?: No
Location: Vancouver, BC
Contact:

Re: BCS tools

Post by bbrally »

I recently changed my web hosting provider. So perhaps if the page can't be found its because your browser has cached the original redirected address. Maybe try Ctrl F5 to do a hard reload.
BrunDog
Posts: 96
Joined: Wed Mar 25, 2015 6:56 am
Bot?: No

Re: BCS tools

Post by BrunDog »

Anyway been using the heck out of this... it ROCKS!

-BD
akschaub
Posts: 4
Joined: Tue Sep 01, 2015 4:39 pm
Bot?: No

Re: BCS tools

Post by akschaub »

Tried to use the temp probe calibration tool and for some reason it can't find my BCS. I'm using chrome and have double checked the correct IP is entered but it says it is unable to connect to the BCS. Version 4.0.0 on the latest build too. Wondering if anyone else is having issues.
bighefty
Posts: 42
Joined: Tue Feb 28, 2012 5:05 pm
Bot?: No

Re: BCS tools

Post by bighefty »

I cannot believe it took me this long to find these tools!! THEY ARE AWESOME!!!

THANK YOU!!!
User avatar
bbrally
Posts: 210
Joined: Sat Mar 27, 2010 3:59 am
Bot?: No
Location: Vancouver, BC
Contact:

Re: BCS tools

Post by bbrally »

akschaub, make sure you are using the full address:

http://XXX.XXX.XXX.XXX

I also don't believe I incorporated any ability to log onto a password protected BCS at: http://calculator.from-ca.com/

I did however incorporate password access to : http://manipulator.from-ca.com/

If you have your BCS password protected, you'll have to disable the password for now.
BrunDog
Posts: 96
Joined: Wed Mar 25, 2015 6:56 am
Bot?: No

Re: BCS tools

Post by BrunDog »

Hey bbrally,

Everytime I try to rearrange states in process 3 (aka the fourth process) using your tool, it screws the states up. Specifically, I am moving State 0 to State 1, 1 to 2, 2 to 3, and moving the blank state 3 up to 0. Just drag and dropping, but afterward its all screwed up, dragging in settings from other processes. It only happens in that process. Could you check the code on that one?
User avatar
bbrally
Posts: 210
Joined: Sat Mar 27, 2010 3:59 am
Bot?: No
Location: Vancouver, BC
Contact:

Re: BCS tools

Post by bbrally »

Brundog, it sounds like your problems are happening after the save, or is this happening on the screen?

I don't have access to a BCS right now, and can't recreate this on screen.

I'll look into creating some dummy data and testing this out over the next couple of days.

Can you provide a specific setting that came from a different state? And if possible what process/state did it come from.
User avatar
bbrally
Posts: 210
Joined: Sat Mar 27, 2010 3:59 am
Bot?: No
Location: Vancouver, BC
Contact:

Re: BCS tools

Post by bbrally »

I finally got access to my BCS and I have been able to duplicate this problem.

I'll try and sort it out over the next couple of days.
User avatar
bbrally
Posts: 210
Joined: Sat Mar 27, 2010 3:59 am
Bot?: No
Location: Vancouver, BC
Contact:

Re: BCS tools

Post by bbrally »

I felt pretty stupid once I figured out how simple my error was. The problem only affected process three by copying process two into it whenever there was a save involving process three.

Hope this didn't negatively impact anyone too much, my apologies.
BrunDog
Posts: 96
Joined: Wed Mar 25, 2015 6:56 am
Bot?: No

Re: BCS tools

Post by BrunDog »

Thanks for fixing! Sorry I couldn't test it further.
Post Reply