After I upgraded to 4.1.1 I have an odd Process Pane
I am running Chrome 62.0.3202.75
I cleared my Browser Cache and did a refresh but this is what I have:
4.1.1 Chrome Issue?
-
- Site Admin
- Posts: 1726
- Joined: Sun Jul 18, 2010 7:51 am
- Bot?: No
- Location: Huntington Beach, CA
- Contact:
Re: 4.1.1 Chrome Issue?
Just had someone else that had some browser oddities with 4.1.1 and a full browser refresh (Shift+F5 on Windows, Ctrl-F5 on Mac) fixed it for him.
Re: 4.1.1 Chrome Issue?
Shift F5 did not change it. I had run a couple of cleaners. I did both a hard and soft reset. I reinstalled 4.1.1 It happens after all of them. I do believe it is a local browser issue, just hoping from some insight as why it would do this. I could re install 4.0.1 and see if that clears the issue.
Re: 4.1.1 Chrome Issue?
Another Clue. I cleaned again including all window caches and logs and current sessions. I installed 4.01 and everything looked good. I reinstalled 4.1.1 and every thing looked good. I was with Factory defaults. I went to networking and changed the Port. That is when it reverted back to the odd Process Pane.
Re: 4.1.1 Chrome Issue?
Another Clue. I changed back to Port 80 and All is well.
Re: 4.1.1 Chrome Issue?
And another: Let's say my Port was 67556 > That gave the bad Process Pane. I changed it to 80 and it is fine. I changed it to 67557 and it is bad again.
Re: 4.1.1 Chrome Issue?
The highest valid port in IPv4 is 65535 and the BCS has a check to reject any ports higher than that. Are you sure you used 67557 and that the BCS saved that change?
Re: 4.1.1 Chrome Issue?
I think this has to do with the browser zoom level. This doesn't seem to be as big a problem in Firefox as Chrome.
Long timer and process names also overflow their container and give readability problems. This occurs in both Firefox and Chrome.
Display at 100% zoom in Chrome:
Display at 80% zoom in Chrome:
Long timer and process names also overflow their container and give readability problems. This occurs in both Firefox and Chrome.
Display at 100% zoom in Chrome:
Display at 80% zoom in Chrome:
Move, copy, clear proc/states: http://manipulator.from-ca.com/
Perform coeff. mods: http://calculator.from-ca.com/
HMI latest ver: http://bbrally.altervista.org/guibeta/i ... r=01042020
Perform coeff. mods: http://calculator.from-ca.com/
HMI latest ver: http://bbrally.altervista.org/guibeta/i ... r=01042020
-
- Site Admin
- Posts: 1726
- Joined: Sun Jul 18, 2010 7:51 am
- Bot?: No
- Location: Huntington Beach, CA
- Contact:
Re: 4.1.1 Chrome Issue?
I can't get it to do that at any zoom level.
On the timer names, I suggested today that we put a hard return in between the process name and the timer name so it is always a two line description. Also might add a flag at the timer level to specify whether it should be displayed in the large timer panel. I personally can have 16 timers running, but I would only want to display 4 large.
On the timer names, I suggested today that we put a hard return in between the process name and the timer name so it is always a two line description. Also might add a flag at the timer level to specify whether it should be displayed in the large timer panel. I personally can have 16 timers running, but I would only want to display 4 large.
Re: 4.1.1 Chrome Issue?
Zoom it is!! I only get it at 80%. Any other zoom is fine. Problem is fixed for me. I was tearing my hair out. I went to a different computer and it was not an issue.
Not sure why it was fine when I had the Port at 80. Maybe because it was also 80% zoom?
My Port is within the correct range, I just made one up for post as I did not want that public.
I use the zoom sometimes so all the LED Gauges are on one line.
Not sure why it was fine when I had the Port at 80. Maybe because it was also 80% zoom?
My Port is within the correct range, I just made one up for post as I did not want that public.
I use the zoom sometimes so all the LED Gauges are on one line.